I get quite a few emails from readers of my blog asking how my QO-100 satellite station is put together and so, I thought perhaps now is a good time to put together an article detailing the complete build.

My QO-100 satellite ground station is built around my little Icom IC-705 QRP transceiver, it’s a great little rig and is ideal for the purpose of driving a 2.4Ghz transverter/up-converter.

Of course all the software used for the project is Opensource and freely available on the internet.

The station comprises of the following building blocks:

• Icom IC-705 Transceiver
• DXPatrol 28/144/433Mhz to 2.4Ghz Up-Converter
• DXPatrol GPSDO Reference Oscillator
• DXPatrol 2.4Ghz 5/12w Amplifier
• Nolle Engineering 2.2 turn 2.4Ghz IceCone Helix Antenna
• 1.1m (110cm) Off-set Dish
• Bullseye 10Ghz LNB
• Bias-T to feed 12v to LNB
• NooElec SmartSDR Receiver
• PC Running Kubuntu Linux Operating System
• GQRX SDR Opensource Software
• Griffin Powermate USB VFO Knob
• QO-100 Ground Station Dashboard developed using Node-RED
• LMR400-UF/RG58 Coax Cable

To get a good clear view of the QO-100 satellite I have the dish mount 3.2m above the ground. This keeps it well clear of anyone walking past in the garden and beams the signal up at an angle of 26.2 degrees keeping well clear of neighbouring gardens.

The waterproof enclosure below the dish houses all the 2.4Ghz equipment so that the distance between the feed point and the amplifier are kept to a minimum.

The DXPatrol amplifier is spec’d to run at 28v/12w or 12v/5w, I found that running it at 28v produced too much output for the satellite and would cause the LEILA alarm on the satellite to trip constantly. Running the amp at 12v with a maximum of 5w output (average 2.5-3.5w) is more than enough for me to have a 5/9+10 signal on the transponder.

The large 1.1m dish gives me quite an advantage on receive enabling me to hear the very weak stations with ease compared to other stations.

The photo above shows the 2.4Ghz equipment mounted in the waterproof enclosure below the dish. This photo was taken during the initial build phase before I rewired it so, the amplifier is shown connected to the 28v feed. To rewire the amp to 12v was just a matter of removing the 28v converter and connecting the amp directly to the 12v feed instead. This reduced the output from a maximum of 12w down to a maximum of 5w giving a much better (considerate) level on the satellite.

It’s important to keep all interconnects as short as possible as at 2.4Ghz it is very easy to build up a lot of loss between devices.

For the connection from the IC-705 to the 2.4Ghz Up-Converter I used a 7m run of
LMR-400 coax cable. The IC-705 is set to put out just 300mW on 144Mhz up to the 2.4Ghz converter and so it’s important to use a good quality coax cable.

Once again the output from the 2.4Ghz amplifier uses 1.5m of LMR-400-UF coax cable to feed up to the 2.2 turn Icecone Helix Antenna mounted on the dish. This keeps loss to a minimum and is well worth the investment.

The receive path starts with a Bullseye LNB, this is a high gain LNB that is probably one of the best you could use for QO-100 operations. It’s fairly stable frequency wise but, does drift a little in the summer months with the high temperature changes but, overall it really is a very good LNB.

The 12v feed to the LNB is via the coax and is injected by the Bias-T device that is in the radio shack. This 12v feed powers the LNA and associated electronics in the LNB to provide a gain of 50-60dB.

From the Bias-T the coax comes down to the NooElec SmartSDR receiver. This is a really cheap SDR device (<£35 on Amazon) based on the RTL-SDR device but, it works incredibly well. I originally used a Funcube Dongle Pro+ for the receive side however, it really didn’t handle large signals very well and there was a lot of signal ghosting so, I swapped it out for the NooElec SDR and haven’t looked back since.

The NooElec SmartSDR is controlled via the excellent Opensource software GQRX SDR. I’ve been using GQRX SDR for some years now and it’s proven itself to be extremely stable and reliable with support for a good number of SDR devices.

To enhance the operation of the SDR device I have added a Griffin Powermate VFO knob to the build. This is an old USB device that I originally purchased to control my Flex3000 transceiver but, since I sold that many moons ago I decided to use it as a VFO knob in my QO-100 ground station. Details on how I got it working with the station are detailed in this blog article.

Having the need for full duplex operation on the satellite this complicates things when it comes to VFO tracking and general control of the two radios involved in the solution and so I set about creating a QO-100 Dashboard using the great Node-RED graphical programming environment to create a web app that simplifies the management of the entire setup.

The QO-100 Dashboard synchronises the transmit and receive VFO’s, enables split operation so that you can transmit and receive on different frequencies at the same time and a whole host of other things using very little code. Most of the functionality is created using standard Node-RED nodes. More info on Node-RED can be found on the Opensource.radio Wiki or from the menu’s above.

I’ll be publishing an article all about the QO-100 Dashboard in the very near future along with a downloadable flow file.

I’m extremely pleased with how well the ground station works and have had well in excess of 500 QSO’s on the QO-100 satellite over the last last year.

More soon …

With the recent explosion of artificial intelligence (AI) art generators that are making the news of late for all the wrong reasons, I decided to see if I could put it to good use and design some futuristic QSL cards.

Having recently been contacted by the Special Callsigns QSL Manager and being advised that there were 18 QSL cards waiting for me, I decided it was time to create some QSL cards of my own for future use.

Having never used any form of online AI and not having any artistic abilities I was amazed how easy it was to create images using nothing more than a paragraph or so of text to describe what it was I wanted to create.

Since all the QSL cards I received were for contacts on the QO-100 satellite, I set out to create a visually futuristic QSL card that was based around a radio HAM operator and satellite communications.

To my surprise the results of my first image generation were surprisingly good. The AI generated an image that resembled the simple text that I entered, although I never requested a one legged HAM operator!

Pleased with my very first attempt I gradually improved the description of what I was looking for, adding more and more detail to the text and including things that I wanted to see in the image. Over a fairly short period of time this approach started to generate some very interesting images.

With each iteration I gradually got closer to what I was trying to achieve but, never quite got exactly what I wanted so, I decided to rewrite the descriptive text adding even more information than before. The text was now a full blown paragraph with quite specific things described including the angle at which the scene was being viewed from.

The other option I wanted to try out was the theme functionality that the AI offered. This allows you to set a theme for the image from things like steampunk, cartoon, manga, real world and many more. The results were quite impressive and added yet another angle to the image generation.

I disappeared down the theme AI Art generation rabbit hole for quite some time and generated some very interesting and fun results. The best by far though was the Thunderbirds themed image, this did put a smile on my face!

At the other end of the spectrum I tried the Salvador Dalli theme, it produced an image that was very like the work of the famous artist but, wasn’t quite what I was looking for.

After much fun I eventually settled on the image I was after, a futuristic scene of a radio HAM with a satellite ground station over looking a mountain range and city below.

I’m really pleased with the results from my ventures into AI generated art. The next challenge is to create a QSL card for HF bands Contacts.

More soon …

Hello and welcome to Episode 546 of Linux in the Ham Shack. In this episode, the hosts take a look at some of the variations of the newly released Fedora …

💾

Hello and welcome to Episode 544 of Linux in the Ham Shack. In this episode, the hosts discuss short topics including Hamvention 2024, the exploit affecting the ARRL and LoTW, …

💾

Hello and welcome to Episode 546 of Linux in the Ham Shack. In this episode, the hosts take a look at some of the variations of the newly released Fedora …

💾

Hello and welcome to Episode 546 of Linux in the Ham Shack. In this episode, the hosts take a look at some of the variations of the newly released Fedora 40 distribution. Topics include installation, desktop environments, ease of use, ham radio readiness, quirks and more. A particular focus is the partitioning system and other potential issues. Thanks for listening and have a great week.

73 de The LHS Crew

💾

Have a couple bits of kit to check out antennas and feedlines. The TDR is sort of like a sonar looking down the feedline/system for anomalies. The bigger analyzer is newly acquired and small is one I have been perfecting “operator error” for some time.   I have a couple project antennas, a couple purchased […]

Have a couple bits of kit to check out antennas and feedlines. The TDR is sort of like a sonar looking down the feedline/system for anomalies. The bigger analyzer is newly acquired and small is one I have been perfecting “operator error” for some time.   I have a couple project antennas, a couple purchased… Continue reading A bit of Antenna Analysis

I took this antenna apart in 2018, and moved it to our Washington Island QTH just in time to have my tower relocation project stall with the CCP-19 Virus outbreak. Six years later it is reassembled. The weather was nice for an hour and pouring rain the next, so I was able to get the […]

It's time once again for The Weekender. This is our departure into the world of hedonism, random topic excursions, whimsy and (hopefully) knowledge. Thanks for listening and, if you happen to get a chance, feel free to call us or e-mail and send us some feedback. Tell us how we're doing. We'd love to hear from you.

73 de The LHS Crew

💾

I took this antenna apart in 2018, and moved it to our Washington Island QTH just in time to have my tower relocation project stall with the CCP-19 Virus outbreak. Six years later it is reassembled. The weather was nice for an hour and pouring rain the next, so I was able to get the… Continue reading Reassembled Tennadyne T-8 Log Periodic on Island

(This a rewrite as WordPress.com ate without leaving the least sign the first draft. Actually self-deleted several drafts and scheduled posts. Not helpful.)   EDIT 9:30 AM June 4th – Seems Powerwerx takes speedy delivery to heart, as my order was just dropped off at my office!  Alas I won’t be able to break into […]

(This a rewrite as WordPress.com ate without leaving the least sign the first draft. Actually self-deleted several drafts and scheduled posts. Not helpful.)   EDIT 9:30 AM June 4th – Seems Powerwerx takes speedy delivery to heart, as my order was just dropped off at my office!  Alas I won’t be able to break into… Continue reading Replacement Power Supplies

A quiet reminder to keep in touch with your friends and family. When people get old and/or take ill, it seems to come in waves. This week a cousin told family that cancer has spread into two areas and types of cancer, which puts things into uncharted territory for them. A friend’s wife who also […]

At one point, the Motorola 6809 seemed like a great CPU. At the time it...

A quiet reminder to keep in touch with your friends and family. When people get old and/or take ill, it seems to come in waves. This week a cousin told family that cancer has spread into two areas and types of cancer, which puts things into uncharted territory for them. A friend’s wife who also… Continue reading Fading Friends and Family

It’s been a busy few months, and the folx who I interact with on Mastodon already know that I’ve got lots of irons in lots of fires. I figured it’s probably time for me to do a quick ‘state of the shack’ post to give a quick highlight on where all my various projects and activities stand, in case anyone has been wondering about the status of any particular item.

So, in no particular order, here we go:

Repeater

Check out the Repeater Page and posts tagged repeater for more details.

The quick summary here, is that my Motorola GR1225 died, so I currently have a machine on the air using a pair of Kenwood TK840 radios, the duplexer from the Motorola, and a new USB interface from Repeater-Builder to connect it to the computer that runs the Allstar software. After some very positive feedback on the post I wrote as I was trying to get the machine running again, I decided to start a fund-raiser to support some upgrades to the repeater, and to also help repair and get some additional repeaters on the air, which brings us to the next project…

r4e

Check out the r4e project pages for more details.

r4e is an acronym for Repeaters 4 Everybody.
As a way to support upgrades on my repeater and some additional repeaters that are operated with a purposeful mission of openness and acceptance, and to help bulk up the RF side of the Pride Radio Network, I’ve started the r4e project which some of you may have stumbled across already in the header of my site. If you’re willing to help support some repeaters financially, or with donations of equipment, or to just connect an existing repeater to the pride network, those gifts and actions can go a long way towards our roadmap!

Subversive Radio

Check out the Subversive Radio Shop for details, and to buy cool stuff!

This project is an offshoot of the r4e project, and is a way to raise additional funds for those projects by selling radio merch that (I hope) is unlike most of the stuff already out there. Buy some cool stuff to support the project!

Radio Rocket

Check out the Radio Rocket Page and the Radio-Rocket Tagged Posts for more details.

Version 3 of the rocket (Ponzu) had some body tube damage during its first flight, which is now repaired, and it’s ready to fly again. I also built a new ground station that is an all-in one unit with the single board computer, LoRa receiver, an RTL-SDR dongle for receiving APRS packets, touchscreen for launch control and data display, etc. Motors are ordered for the next launch, which will be on June 13th or 14th, as weather permits.

Club Net

Check out the Narwhal Amateur Radio Society, and our Nets Page (details coming soon, if they aren’t already there!) for more info.

A while back I joined the Narwhal Amateur Radio Society (NR7WL) - they’re a relatively new club, but have values that I dig. We had kicked around the idea of a club ‘network’ to be able to connect via digital modes, and potentially a club net. That idea sat for a little bit, but bubbled back up recently, so I took the initiative to set up an Allstar node for the club (61672) which will serve as our hub, and the location for our first club net, for which I’ll be serving as net control!

Net details as follows:

Narwhal Amateur Radio Society Club Net

Time: 1st Tuesday of Every Month at 7pm Pacific, 10pm Eastern

Location: Hosted on the NR7WL Allstar Node (61672) and the Pride Radio Network. The Pride Radio network has bridges that will allow you to connect via DMR, IRLP, System Fusion, M-17, NXDN, P-25, D-Star, Echolink, Hamps Over IP, Hamshack Hotline, plus others!

Shack

Check out posts tagged shack for more details.

I haven’t made any major updates to the shack recently, but I have moved a few things around. In the utility space behind the operating position I added a DIY rack made from lumber to move the various computer and network bits and bobs into. My next project in the shack is related to re-doing some of the audio routing - I have designs drawn up in KiCad for an interface device that will sit beside my mixer and convert all the audio to the OHIS standard. The basic reasoning behind this for me, is that by converting the audio to OHIS, I can leverage an existing standard to run a single shielded cat6 cable to each radio and device, instead of the 3 or 4 audio and PTT cables that run to each radio now. I currently have some bursting-at the seams cable management, and doing this should reduce the mess in there quite a bit. The plan is also to eventually replace my aging mixer, and build a new rack mount arrangement to the left of my operating position to house the mixer, interface, and some other related shack equipment.

ARIP

Check out the ARIP website for more info.

Diversity is something important to our hobby. If you disagree, or think this statement is somehow political, you’re part of the problem in the hobby, and I won’t engage with you on the subject. If you do feel the same way I do however, the ARIP is one of my projects that is essentially a tool that clubs, individuals, or other organizations can use as a way to show their commitment to inclusion in the hobby. The most recent update on this effort is some changes to the website and methodology to make it more of a self-serve tool. There is more information about that available on the ARIP Website

Radio League of America

Check out the Radio League of America website for more info.

Currently, the Radio League of America (RLA) is little more than an idea. That idea being that the amateur radio community is too large and diverse for everyone to have their voices heard by a single national organization. There are many amateurs who have voiced a desire for something different to be available, and the RLA is just one of many potential avenues as that movement takes life. I have committed to at some point in the near future getting together an initial presentation of what that might look like, and setting up a recurring (probably quarterly) series of meetings for people who are interested to see if it is something worth fleshing out in more detail and organizing around.

Hello and welcome to Episode 544 of Linux in the Ham Shack. In this episode, the hosts discuss short topics including Hamvention 2024, the exploit affecting the ARRL and LoTW, …

💾

Hello and welcome to Episode 544 of Linux in the Ham Shack. In this episode, the hosts discuss short topics including Hamvention 2024, the exploit affecting the ARRL and LoTW, Winamp, Rufus, a discussion on privacy in social media and much more. Thanks or listening and have a great week.

73 de The LHS Crew

💾