Remember yesterday when I mentioned the latest addition to my POTA setup, the Xiegu 5105 QRP rig….

Well this morning I decided to test it out and see how much work I would have to do with setting the parameters such as mic gain, processor, to make it sound like me… I was also testing out my EARCHI 9:1 unun with a 29.5 foot random wire to see how it would play with the built in AT of the 5105.

I figured I might as well do the testing at a POTA location just in case I was able to turn the test into an activation.

For this I chose Fort Frontenac POTA CA-5303. Its fairly easy to get there via the Kingston Transit system and its also close to downtown and all the amenities I might need. In the North East corner of the picture you will notice some white lines on the ground.

They are actually the walls of what’s left of that part of the Fort. Also the only parts of the Historic Site that is open to the public.

I leaned my MFJ 33 foot mast (supporting the 9:1 and wire in the vertical configuration) up against the tree.

And then ran the COAX over to the remains of the wall and set up my radio there and started operating.

My first contact was on 7.255 with the NCS of the ECARS net. He did hear me and considering I was QRP I was pleased. He did tell me that my audio seemed hot as if I was overdriving things. Lowering my voice seemed to help.

After that I looked at POTA Spots and managed to get W2IDG and VE3FI into the log from their parks and then finished up with the NCS of the MidCars net on 7.258.. All contacts were made on 40m SSB. I tried 20 SSB and was hearing lots of stations including a POTA Activation in VO1 but no luck breaking any of the pileups.

Then I figured it was time to get home and try to re configure the radio to my liking… I turned off the Speech Processor and lowered the Mic Gain from 60 to 40. Over the next few days I will get out again and see what else I have to do to get things sounding right.

Till then

73bob

People who know me have heard me say that after all these years there are 3 radios I have sold that I actually regret selling. Well now there are only 2 radios that I regret selling…

.

Welcome the Xiegu X5105 back into my portable shack…

.

Between my FT991a and my FT891 there was a bit of a gap. The Yeasu FT891 Portable Station was a bit too heavy for my old bones. I needed something in a lighter backpack to make it easier to carry if I was to choose to activate one of the local POTA Parks here in Kingston.

The above pic shows my old X5105 with the Bandspringer attached

The Xiegu X5105 fills that gap. With the built in battery pack, the built in automatic antenna tuner along with the contest keyer and the built in CW Decoder it makes it a dream portable station.

My antennas are a 40m EFHW made with 28ga wire and a QRP AMAZON 49:1 unun. I also can use a 29foot end fed random wire using a QRP EARCHI 9:1 unun.

I also have the SOTABeams Bandspringer antenna that plugs right into the antenna input and uses the built in tuner to operate between 10m and 60m.

So what’s the other two radios you might ask?

Above is my first QRP setup. FT817, LDG QRP Autotuner.

If I could work a deal for a Yaesu FT817 and a Flex 1500 it would complete the list. However used rigs are pricy and it seems most hams think that radios seem to appreciate with age so like I mentioned above it has to be a good deal for both the seller and myself.

73bob

People who know me have heard me say that after all these years there are 3 radios I have sold that I actually regret selling. Well now there are only 2 radios that I regret selling…

.

Welcome the Xiegu X5105 back into my portable shack…

.

Between my FT991a and my FT891 there was a bit of a gap. The Yeasu FT891 Portable Station was a bit too heavy for my old bones. I needed something in a lighter backpack to make it easier to carry if I was to choose to activate one of the local POTA Parks here in Kingston.

The above pic shows my old X5105 with the Bandspringer attached

The Xiegu X5105 fills that gap. With the built in battery pack, the built in automatic antenna tuner along with the contest keyer and the built in CW Decoder it makes it a dream portable station.

My antennas are a 40m EFHW made with 28ga wire and a QRP AMAZON 49:1 unun. I also can use a 29foot end fed random wire using a QRP EARCHI 9:1 unun.

I also have the SOTABeams Bandspringer antenna that plugs right into the antenna input and uses the built in tuner to operate between 10m and 60m.

So what’s the other two radios you might ask?

Above is my first QRP setup. FT817, LDG QRP Autotuner.

If I could work a deal for a Yaesu FT817 and a Flex 1500 it would complete the list. However used rigs are pricy and it seems most hams think that radios seem to appreciate with age so like I mentioned above it has to be a good deal for both the seller and myself.

73bob

Need to charge your tablet or laptop computer off-grid? This video shows you how to do it.

Power Queen LiFePO4 Prime Day Sale for USA & Europe. Pay Attention!

A DIY Victron Cerbo touschreen to save some money on monitoring battery storage and solar energy.

Traditionally held on “The Last Rainy Weekend” in June but for the sticklers for the rules its actual date is the 4th weekend in June…

This year it would be on June 22nd and ending on June 23rd

So what will VA3QV be doing???? Its safe to say that my Field Day Station will look a bit like this:

or like this from back in 2017….

So I plan to be operating as a 1B Battery Station from the RAC Ontario East Section (ONE)

The actual location has not been determined yet but there is a good chance the location could be one of the Parks on the Air location in the City of Kingston.

That’s the plan for good weather… and so far the long range forecast is calling for nice (dry). If the weather is not dry then the plan is to operate as a home station in the 1D catagory just to give out points to the participants

If you are new at this then the rules can be found here:

Years ago Field Day was considered a test of our emergency operating skills specifically to set up and operate a station for 24 hours and somehow it has morphed into more of contest with groups of operators putting up equipment that would not be used in a real emergency at power levels that could not be maintained unless you had a generator and an endless supply of gasoline.

I’m a little more primitive by setting up my QRP (5w of power) radio with a wire antenna and using a solar panel to top up the battery as needed.

I will have the option of being under cover (see above pic) as protection from the sun and/or rain most likely be needed at some time . Not sure how long I will be operating but it won’t be for the full 24 hours.

Overnight all I would be doing is listening to static and feeding the mosquitoes…

No egos to stroke…. Just operate and make some contacts with the emphasis of having fun and not taking myself too seriously.

Hope to hear you and be heard by you during the event

73bob

Power Queen Bluetooth Smart Edition LiFePO4 battery and charge controller test.

Well its not as bad as indicated from my last post…

But its still got a way to go…

This morning on my 11 am (Eastern) hour on the TPN I managed to get 7 stations in my log which is the best its been in a while. After the net ended I had some household chores to do before I could get to the next part of this post.

Today I wanted to take my Yaesu FT891 rig along with my two antennas out into my backyard and make sure everything is still working as well as I remember. Next week my shifts on the TPN will be ending for a while as I am taking the summer off in an attempt to concentrate on my POTA part of the hobby.

So here’s the setup

Rig: Yaesu FT891 powered by my ECO-Worthy 20ah LI-PO4 battery

Antenna 1: 40m EFHW which is 63 feet long and fed by a 64:1 unun. This antenna usually is used in a sloper or inverted Vee configuration. Its very nice on 10-40m and I have 2 small counterpoises which I clip on as needed. I feed the unun from a 25 foot run of RG58 with a RF choke at one end.

Antenna 2: 17.5 foot long end fed fed by a 9:1 unun. I normally would use this in a vertical or sloper configuration. Its excellent on 10m to 20m but will also work on 40m without the need of a tuner. Depending on the situation I have a couple of small counterpoises I can clip onto the unn if needed. I feed the unun from a 25 foot run of RG58 with a RF choke at one end. The advantage to this antenna is that if I use it as a vertical there is next to no footprint which could make a couple of the parks in the downtown area much easier to activate.

If the trees do not cooperate I also carry a MFJ 33 foot telescopic masting which will support the wire if needed.

How did I do today?

Operating from my deck I strung out the 63 foot EFHW kind of as an inverted xyz configuration. Hanging 63 feet of wire anywhere I could hand it without anyone seeing it or running into it. Despite the setup Contacts were made on 40m and 20m despite the band conditions. with a reasonable SWR (no tuner in line) where I normally use it

Next I used the 17.5 with the 9:1 unun as a low sloper and made 1 contact on 20. The SWR was “tolerable” on 40m but on 10m to 20m it was under 2:1 which is great for a Portable setup. Nothing to complain about on my part.

I also use this style of antenna at home in a vertical configuration and it works great for my need either “home or away”

So here’s the plan…

If you notice the above map there are 10 POTA sites (yellow dots) that I can easily access from my home in Kingston. All of them easily reachable via public transit or a bit of a walk. The one on the bottom right (the island) is not reachable via foot. There is a dock but I can’t find out if Kingston has a Water Taxi so if I can activate 10 out of 11 I will be pleased.

I guess I could also say that this would be a test of the station I will be using for Field Day this year. Not sure where I’m going to be yet but…. I know I’ll be participating from somewhere near Kingston.

.

Till next time

73bob

Well its not as bad as indicated from my last post…

But its still got a way to go…

This morning on my 11 am (Eastern) hour on the TPN I managed to get 7 stations in my log which is the best its been in a while. After the net ended I had some household chores to do before I could get to the next part of this post.

Today I wanted to take my Yaesu FT891 rig along with my two antennas out into my backyard and make sure everything is still working as well as I remember. Next week my shifts on the TPN will be ending for a while as I am taking the summer off in an attempt to concentrate on my POTA part of the hobby.

So here’s the setup

Rig: Yaesu FT891 powered by my ECO-Worthy 20ah LI-PO4 battery

Antenna 1: 40m EFHW which is 63 feet long and fed by a 64:1 unun. This antenna usually is used in a sloper or inverted Vee configuration. Its very nice on 10-40m and I have 2 small counterpoises which I clip on as needed. I feed the unun from a 25 foot run of RG58 with a RF choke at one end.

Antenna 2: 17.5 foot long end fed fed by a 9:1 unun. I normally would use this in a vertical or sloper configuration. Its excellent on 10m to 20m but will also work on 40m without the need of a tuner. Depending on the situation I have a couple of small counterpoises I can clip onto the unn if needed. I feed the unun from a 25 foot run of RG58 with a RF choke at one end. The advantage to this antenna is that if I use it as a vertical there is next to no footprint which could make a couple of the parks in the downtown area much easier to activate.

If the trees do not cooperate I also carry a MFJ 33 foot telescopic masting which will support the wire if needed.

How did I do today?

Operating from my deck I strung out the 63 foot EFHW kind of as an inverted xyz configuration. Hanging 63 feet of wire anywhere I could hand it without anyone seeing it or running into it. Despite the setup Contacts were made on 40m and 20m despite the band conditions. with a reasonable SWR (no tuner in line) where I normally use it

Next I used the 17.5 with the 9:1 unun as a low sloper and made 1 contact on 20. The SWR was “tolerable” on 40m but on 10m to 20m it was under 2:1 which is great for a Portable setup. Nothing to complain about on my part.

I also use this style of antenna at home in a vertical configuration and it works great for my need either “home or away”

So here’s the plan…

If you notice the above map there are 10 POTA sites (yellow dots) that I can easily access from my home in Kingston. All of them easily reachable via public transit or a bit of a walk. The one on the bottom right (the island) is not reachable via foot. There is a dock but I can’t find out if Kingston has a Water Taxi so if I can activate 10 out of 11 I will be pleased.

I guess I could also say that this would be a test of the station I will be using for Field Day this year. Not sure where I’m going to be yet but…. I know I’ll be participating from somewhere near Kingston.

.

Till next time

73bob

OH8STN Portable Ham Radio on Solar Power GIVEAWAY 2024.

The off-grid ham shack is fully energy self-sufficient, utilizing solar, wind, and other power sources, with a focus on low current devices for sustainable communication.

March 2024 Power Queen promotions offer discounts for large LiFePO4 batteries in the US and Europe, plus a 5% discount with code...

Integrating the Ruuvi Gateway and sensors to remotely monitor indoor/outdoor temperatures, ensuring safe temperatures for lithium battery charging. Off-Grid Ham Shack

To protect lithium batteries from cold while charging, a video/blog showcases using a Chinese diesel heater in an off-grid ham shack. It's vital to keep batteries above freezing, a lesson learned from electric cars in winter. The video details the installation and operation of a 3kw Vevor diesel heater, which also powers up using the ham shack's LiFePO4 batteries, maintaining ideal temperatures for both batteries and equipment.

This video shows charging Power Queen LiFePO4 batteries with a vertical wind generator and discusses off-grid ham shack power storage solutions, including during non-solar conditions.

This tutorial demonstrates how to connect two 12-volt batteries in parallel using Power Queen 12.8V, 100Ah, 1280Wh lithium iron phosphate batteries. The provided YouTube link offers a detailed guide. For related content, explore building a solar-powered Off-Grid Ham Radio Station and information on radio-friendly MPPT charge controllers and off-grid communications.

The blog post highlights the benefits of Power Queen LiFePO4 batteries for off-grid projects over traditional lead-acid batteries, focusing on the better performance and cost-effectiveness in the long run. Additionally, it provides subscribers with information and discounts on Power Queen's Christmas offers, and illustrates how LiFePO4 batteries function in an off-grid system. It also includes descriptions and respective links of the batteries suited for specific needs in the US, Europe, and Canada.

The author discusses choosing a solar charge controller suitable for radio communication. He focuses on three criteria: portability, radio frequency quietness, and Maximum Power Point Tracking (MPPT) functionality. Recommending Genasun due to its compatibility with these requirements, he mentions his dissatisfaction with another brand, Victron, that caused excessive radio frequency noise. For optimal results, he suggests keeping devices DC powered and using no inverters. He provides specific instructions about matching controllers to battery and solar panel specs, and suggests parallel configuration for Genasun controllers.