Looking for a versatile transceiver thatβs perfect for roving during VHF contests, drive-up SOTA operations, Super High Frequency activity, everyday use in your home station, and a whole lot more? Youβll find all this and loads of fun with the Icom IC-905 VHF/UHF/SHF All Mode Base/Portable Transceiver, says Michael Murphy, KI8R, who covers the features and benefits of this rig in the video below.
Key Features & Benefits of the Icom IC-905:
The IC-905 features a separate controller and RF module, allowing for the installation of the weatherproof RF module near the antennas. A LAN cable makes the connection between the controller and the RF module, significantly reducing power loss. PoE (Power over Ethernet) technology provides flexibility and simplifies the installation of the RF module.
Do you belong to your local u3a group? Are you keen to share your passion for amateur radio with others? As part of the RSGBβs commitment to grow the hobby, the Society would love to hear from RSGB members who would like to spread the word to local u3a groups. As we all know, getting [β¦]
Rugby Amateur Transmitting Societyβs Annual Radio Rally is taking place today, the 18 August, at Princethorpe College, Princethorpe, Rugby. The doors are open from 10am to 4pm, the admission fee is Β£4 per person and pitches cost Β£20. For more information email rally@rugbyats.co.uk or visit the website West Manchester Radio Clubβs Red Rose Summer Rally [β¦]
Bushvalley Amateur Radio Club is active from all three lighthouses on Rathlin Island today, the 18 August. Operators are working on the 80 to 10m bands using SSB, CW and FT8. Listen out for special event callsigns, GB1RP, GB2EL and GB2WL which will all be in use. For more information, visit the QRZ.com page for [β¦]
Frans, DJ0TP is active as TK/DJ0TP from Corsica, EU-014, until the 4Β September. The station was spotted recently on the 20m band using FT8. QSL via Fransβ home call and Logbook of the World. Jean-Louis, F6ITS left France in August 2023 for a round-the-world voyage. He recently obtained a Gambian licence and will be active as [β¦]
On Tuesday 20 August, the 1.3GHz UK Activity Contest runs from 1900 to 2130UTC. Using all modes on the 23cm band, the exchange is signal report, serial number and locator. The World Wide Digi DX Contest starts at 1200UTC on Saturday 24 August and runs until 1200UTC on Sunday 25 August. Using FT4 and FT8 [β¦]
Also, please note that links below ending with an asterisk are affiliate links. Purchasing through those links doesnβt cost you more and I get a tiny amount to help offset some of my costs in crafting The Random Wire newsletter and podcast for you. I appreciate your support.
First, let me describe what I mean by the word restomod? Resto refers to restoration, implying older, vintage equipment. Mod is for modification, but also think βmodern.β Restomodding is the process of converting an old piece of equipment so that it has modern capabilities, making it function like something new while retaining the outward appearance of the original.
Restomod: Classic cars that combine original exterior styling with modern applied technologies (such as new suspension, wheels, transmission) or modern interior features (multimedia, etc.) for comfortable everyday use.
For this amateur radio project, I am restomodding a Kenwood PC-1A Phone Patch Controller case to function as a modern AllStarLink radio-less audio interface.
1.2 Parts
There are some new parts added to the list previously described in Random Wire Review issue 102. Listed below are the parts and supplies for this build...so far! (If there is an asterisk beside a link, that means it is an affiliate link.)
So far, Iβve removed the following items from the PC-1A case: the original board from the PC-1A, a front panel switch, a real panel plate, and the power cord. Still left mounted are: the 8-pin microphone connector, a VU meter, two potentiometers on the front panel, a sliding switch on the back panel, and another potentiometer on the back panel.
Amplifiers
I did find a few of these items in my parts bins. The LOSC-brand PAM8406 board is one I picked up a few years ago. And it turns out I have a baggy full of XL6009 buck boosters.
The PAM8406 board can be configured as a Class D amplifier or a Class AB amp. The defaults on the board are (a) Class D amp, (b) shutdown disable, and (c) mute disable. All those are fine so I wonβt have to change the defaults. The marks that look like fingerprints on the bottom of the board? Thatβs how it came from the overseas vendor!
As I started to fiddle with how the PAM8406 board would fit, I discovered that the board is so long that it interferes with the second potentiometer hole in the front of the case. Instead of using the board I already have, I ordered a couple of these small units: NOYITO PAM8406 Digital Amplifier Board 5W 5W Dual Channel Stereo Audio Module*
These smaller PAM840 amps arrived yesterday. Here are two photos:
I have to confess that the LOSC-brand board looks stouter than the tiny NOYITO board. Maybe itβs the two electrolytic capacitors on the LOSC board that give this impression. Looking at the lack of those caps on the NOYITO board makes me think I might need to consider electrolytic capacitors with the NOYITO board.
Potentiometers
This should give me room to use two 5K⦠potentiometers on the front panel. A fallback would be to put one of the potentiometers on the back panel and use that location for adjusting microphone gain, but that is less convenient than having it on the front panel.
I think it makes the most sense to put the potentiometer for the PAM8406 amp in the RX GAIN position. This would control volume to the external speaker. The TX GAIN position would have the other potentiometer to allow microphone gain to be boosted through the MAX9814 board.
At this point, I removed the original pots from the PC-1A front panel to make it easier to see the positions Iβm describing: RX for external speaker volume and TX for microphone gain.
The original potentiometer knobs fit the modern pots well enough so Iβll try to use them to help maintain the illusion of an original device. The new 5K pots fit well in these two holes.
Capacitors
Iβm out of electrolytic capacitors. I could use one on the 8-pin microphone connector and another on the feed to the VU meter. Capacitors should help smooth out the operation of these devices. I ordered an assortment so I wonβt run dry:
I havenβt yet sketched out how to put all the pieces together but Iβve been making audio notes while I drive. Talking about it helps me think through how the components will work together.
2. Tools
2.1 Two inexpensive multimeters purchased
I think my halfway decent multimeter is in storage somewhere so I did the unthinkable β I drove to my local Harbor Freight and bought a new multimeter. Why would I do such a thing? Convenience, pure and simple.
The Ames Dm1000 looks durable and comes with a case. For my general use (household and vehicles) it is probably more meter than I need. For amateur radio work, it should be sufficient for most tasks, even if measurements prove to be a bit off.
Could I have done better? Certainly. Was there a convenient place to just pop in and buy a reasonable multimeter? Not really. Harbor Freight met my requirements today.
Iβm sure Iβll hear some comments about trusting anything from Harbor Freight. Iβve certainly had that opinion in the past. Today, though, as I examine this device, I feel like the overall quality is a bit better than in years past, at least with some thoughtful examination of the products by the shopper.
Unlike the Ames multimeter, the Kaiweets device does not come with a case.
2.2 Comparing the two multimeters
Letβs take a look at the physical characteristics of the two devices: the more expensive Ames DM1000 ($70) and the cheaper Kaiweets HT118A ($40). Iβm not equipped to opine on the accuracy, precision, or reliability of the units.
The Kaiweets unit takes two AA batteries, accessible through a panel on the back of the device. A single screw secures the door to the battery compartment. The Ames device is similar except it takes a single 9-volt battery.
The form factor and size are similar for the Kaiweets HT118A and the Ames DM1000 devices. However, the Ames device weighs more than (half again as much?) as the Kaiweets. Frankly, the Ames meter feels solid and the Kaiweets feels cheaper, as in lighter in weight and more βplasticky.β
The wire leads for the probes are not the kind that seem to adhere to each other. Leads that stick together drive me nuts. The insulation on the Ames probe leads feels a little more rubbery and substantial than with the Kaiweets device. Both sets of leads are adequate. Both devices also come with a temperature measuring probe.
The main dial control functions fine on both units, but the dial on the Ames device is simpler and less crowded. To my eyes, the dial on the Ames meter is easier to read.
The displays are quite readable for both devices.
Here the devices have backlighting turned on and both are propped up using the integrated leg stand that pops out from the back of the device.
Both devices claim to be true RMS devices. Both boast max voltages of 1000V CAT III and 600V CAT IV. Both have a max 600mA fuse. Both claim to have 6000 count accuracy.
Interestingly, both devices have a non-contact voltage detection (NCV) feature. The two devices differ in how they display NCV detections. The Kaiweets device is simpler: turn the dial to the βNCV Liveβ position and hold the sensor at the top of the device near the suspected circuit. In the gallery below, you see that the light switch in the OFF position generated a different response (green indicator on the meter and L on the display) than when the light switch was ON (red indicator and H on the display).
For the Ames device, the NCV procedure was a bit less clear: turn the dial to any position and hold down the NCV button. The meter did not differentiate between the light switch in the OFF position and when it was in the ON position. In both instances, the meter displayed a red indicator light.
The Kaiweets device seems a bit more intuitive in actual use because the dial includes the NCV setting and because it has a small nubbin on the top of the meter to indicate where the sensor is. I think the difference between the green light and the red light on the HT118A NCV detector is this: the green light is indicating a circuit is present and the red light indicates electricity is flowing through the circuit. This is an interpretation on my part as this is not described well in the small manual. (Someone please correct me on this.) For homeowners checking residential circuits, the Kaiweets HT118A meter seems a bit easier to use.
Of the two, the more expensive Ames meter feels heavier and more solid, the main dial is less βclicky,β and the probe leads are slightly more substantial. Still, for a toolbox meter for the household or vehicle, the Kaiweets may represent good value. Just be sure to put it into a case of some kind to protect it and to keep the parts together!
Iβll give the overall nod to the Ames DM1000 multimeter. It feels more substantial overall, the dial feels and sounds not too βclicky,β the leads are more substantial, and it comes with a case. The Ames unit feels like it might survive a drop or two, compared to the Kaiweets device. (No drop tests were performed to examine this conclusion!) I feel like I can trust the Ames DM1000 meter more than the Kaiweets meter.
I didnβt expect to have three XHDATA radios. I thought Iβd just try one (the D-808) but then XHDATA offered the D-608WB and the D-200 for me to review. The D-808 satisfies my desire for airband coverage.
Overall, Iβm liking the D-808 and D-608WB radios. While the D-808 is not quite the same as a Tecsun-brand radio, it is comparable and perfectly fine for listening to the bands I want. (My Tecsun radio lives in the camp trailer where we depend on it for information when cell coverage is poor.) The D-808 was well reviewed on SWLing.com.
The D-608WB radio is actually a fine unit. This type of household emergency radio is intended to be kept on hand for weather alerts and receiving information over commercial radio frequencies. As such, the radio needs an alternate means of charging, a flashlight, and reasonable performance on AM and FM bands. NOAA weather alert is a must and shortwave reception is a plus.
The D-608WB checks all these boxes and more. Charge it over a USB-C connection, or with a hand crank on the back, or with the solar panel on top. It uses a standard 18650-size battery so itβs easy to keep a spare on hand. It has the obligatory flashlight but also has a variable output LED light underneath the solar panel, good for area lighting in a tent or for late night reading. By the way, the solar panel tilts to help you capture the most energy from the sun.
You can pick up a D-608WB from Amazon* for not a whole lot of money. This unit feels solid, performs well, and has all the features I want in an emergency radio. I like this little unit more than any other emergency radio Iβve tried. Itβs a keeper.
Iβm listening to it while I write this. I have a microSD card with dozens of my favorite albums inserted into the radio and it is playing in the background for my wife and me. Unlike many small radios, it has a bass port on the back of the radio body that makes it more pleasant to listen to.
Iβm still reviewing the D-220 so more on that to come.
4. Random Observations
4.1 Hams talk about their equipment
We hams are a funny bunch. When friends call each other on the phone, they donβt lapse into descriptions of their gear: βIβm calling on a Samsung model SM-G781U via my home wifi, using a headset thatβs a bit of a homebrew.β People just donβt do that, but we hams do exactly this when we talk to each other on the radio. That, and report on our local weather and compare health issues.
4.2 Cell phones, automatic gain control, and audio quality
I also note that cell phone manufacturers have done a tremendous job with what Iβll call automatic gain control (AGC). AGC automatically adjusts the strength of an input. On the smartphones Iβve used, one can talk close to a microphone or several inches from it, and on the receiving end, it can be hard to tell if the talker is close to the microphone or not. Not so with our amateur radio gear! Distance from a microphone makes a huge difference in audio quality. I routinely hear stations with audio that is distorted because the person speaking their lips up to the microphone and is speaking loudly.
Checking our own audio using a Parrot ought to be part of our regular radio practice, even if only once a year. I tried a parrot on WIRES-X at 41619 but got no response. Iβm looking for other WIRES-X parrots. Suggestions are welcome!
Will the 0.0.0.0 Day bug affect AllStarLink nodes? This thought surfaced as I was reading a security article titled 0.0.0.0 Day: Exploiting Localhost APIs From the Browser. In the configuration of AllStarLink nodes, sometimes we use 0.0.0.0 as the IP address in a configuration file. For example, my manager.conf file has this set in the [general] setting:
bindaddr = 0.0.0.0
Binding the IP to 0.0.0.0 provides no additional security beyond the username and password for the node. Iβm not particularly worried about this on my home node because (a) Iβm operating inside my local network and (b) I use a VPN to reach the node from outside the network. Setting the bind address to 0.0.0.0 is a convenience for me.
Is there risk in doing this? I suppose there is but I deem it an acceptable risk for my use case.
5.2 Multilayered attacks
Recently, an entity I work with was affected by bad actors. In popular parlance, they got hacked and lost a chunk of money.
The attack vector started out as you might expect β someone clicked a link they should not have clicked β but it escalated from there to a much more sophisticated operation. Iβm still gathering information on this but wanted to get this warning out to my subscribers: be careful what you click! Bad actors are becoming more surgical in their approach and more convincing in their interactions.
If you have not yet enabled multi-factor authentication (MFA) now is the time. I resisted doing this for quite a long time because having to enter something more than my username and password seemed like too much bother. Considering the potential for harm, though, it really isnβt too much bother. If nothing else, you should have MFA enabled for your email and banking/investing services.
I now use random passwords, MFA, and USB security keys to help protect my assets.
6. Miscellaneous
6.1 Inline switch (DC)
The Behringer mic (C-1 medium diaphragm condenser microphone*) and pre-amp (MIC500USB audiophile vacuum tube preamplifier*) combo I bought from a seller on Amazon came with a power supply that did not work. (That might be why I got it for such a great price!) Fortunately, I already had a suitable power supply for one of my Dell Wyse 3040 thin client units that worked perfectly with the Behringer package.
However, to power up the pre-amp you plug the 2.1mm plug into the receptacle on the back of the pre-amp. Alternatively, you can keep that plugged in and plug in (and remove) the wall wart from the 120V socket. Neither method is convenient and both introduce wear on these components.
Instead of manually plugging and unplugging things, I bought a package of inexpensive inline switches. I gambled that the 5.5mm x 2.1mm plugs on the switch would work with the Behringer unit, and it works great.
This lets me keep the Behringer pre-amp plugged in at all times. When I need to use it, I power it up. When I donβt need it, I power it off. I donβt know if this introduces noise into the audio circuit but so far, itβs been fine. The podcast for this issue was recorded with the Behringer mic and pre-amp package using this little switch. This is my kind of solution: simple and effective!
Hereβs another plus: this switch (there were four in the package) fits some of my Dell Wyse 3040 thin client devices, too.
6.2 Replacement WisMesh Pocket received
On Tuesday, I received a replacement WisMesh Pocket device from Rokland Tech. I reported on the original unit in issue 100.The one point in common with the two RAK-based Meshtastic devices that have failed is my USB-C charger. For the new WisMesh Pocket device, Iβm charging on a very low-powered charger. Weβll see if that makes a difference.
Kudos to Rokland Tech for their help. The replacement device worked right out of the box. It shows up on the MeshMap.
6.3 New-to-me Ten-Tec Scout 555 on the way
Buying something off eBay is always a bit of a crap shoot. I rolled the dice and purchased a well-used Ten-Tec Scout 555 transceiver. (I do like a simple radio!) In the photos, the case looks a bit rugged in spots but the front panel, display, knobs, and rear panel look reasonably pristine. I have another old Scout 555 (reported in issue 96) that may not be working quite right so what is in a side-by-side comparison. If there is actually a distinct difference between the transceivers, I might do a bit of mix-and-matching to make one good working machine.
Our simple one transistor Michigan Mighty Mite creates a CW (Continuous Wave) signal simply by powering on and off the circuit. Involving less than a dozen components, this is truly a spare design. Without some attention to the keying (Keying Shaping) and the type of crystal being used or how it is tuned for maximum smoke (TFMS) it could and will sound like crap. Crap here does not mean Cool Radios And Projects!
The letter "K" ( _._ ) might look like this sent in CW. But this is pretty idealized waveform and given the items mentioned earlier might not be so clean.
Given the long stretches at the Board and Care where I am just sitting there while the XYL naps, my mind wanders to thoughts of CW generation using other topologies.Β
Those with SDR radios who operate CW -- ever wonder how you generate CW using I/Q or DDC. Well, I am not totally sure how it is done but it certainly more than keying a single 2N2222A.
Most likely the CW generation in SDR involves a generated audio tone that with filtering appears like a brick wall square wave which is then translated in a mixing process to the operating frequency.Β
Then I thought about Modulated CW and in an attempt to be accurate looked up MCW. Here is what Wikipedia said.
Modulated continuous waveΒ (MCW) isΒ Morse codeΒ telegraphy transmitted using an audio tone to modulate aΒ carrier wave.
Continuous wave (CW), by contrast, does not use a subcarrier, so there is no emission at all between Morse code symbols.
MCW can be generated by any AM or FM radio transmitter with audio input from an audio oscillator or equivalent audio source.[1][2]Β When an SSB transmitter is modulated by Morse code of only a single audio frequency, the resulting radio frequency emission is J2A or J2B and therefore is CW by definition, not MCW.[3]
Using a divining rod as a magic decoder ring, this I think is saying were you to modulate an AM signal with an audio tone, when no audio tone is present then you still have the carrier present. Whereas if you use SSB (no carrier) then on key up no carrier so true CW. I would think this might extend to a DSB transmitter that has no carrier. So, using DSB would not be MCW but CW.
When I built the MC1496 Direct Conversion Receiver using the Motorola (On-Semi) data sheet there was a schematic for a DSB Transmitter.Β I tried my hand at a DSB transmitter using the MC1496.
So, what if we built another MC1496 configured as a DSB transmitter and introduced an audio tone of around 600 Hz into the circuit and then we would have CW (by our Wikipedia definition). The Arduino Code for the DCR could be modified for the DSB transmitter with the necessary control circuits and generating an audio tone already exists.Β
This could be yet another way to do the CW transceiver. As of now this is just a brain message sent to me at 3AM this morning. It is not ready for prime time -- just yet.Β
More thought is needed on this approach but HAS a huge advantage if it can be pulled off. You would have both a CW and SSB (well DSB) transceiver with no Filter to be fiddled with using a questionable Nano VNA.
The RSGB Convention is just eight weeks away and the programme is shaping up to be a fantastic mix of interesting presentations for every radio amateur, regardless of experience. There will also be practical sessions and time to chat to representatives from RSGB committees and groups. For a reminder of the wide range of RSGB [β¦]
Ofcom has released a new step-by-step video on its YouTube channel to assist radio amateurs in the process of revalidating a UK amateur radio licence using the online licensing portal. Ofcom does note that whilst it is a requirement to revalidate your licence every five years, it is recommended to do it annually. Make sure [β¦]
For all the details. please go toΒ https://www.qsl.net/w2lj/ - Skeeter numbers will be handed out right up until Midnight Saturday/Sunday EDT. After that, the roster is closed. Thanks to all of you who have signed up so far. As of this morning, as I type this, we have 209 Skeeters waiting to take wing.
W2LJ will most likely be working from the shack this year. The weather outlook for Sunday in NJ is still terrible. Rain showers all day with possible thunderstorms in the afternoon. I was going to set up in the backyard, but unless a weather miracle occurs, that's not going to happen. I do enough stuff that merits God hitting me with a lightning bolt. No sense in making it easier for Him. LOL!
Although, I just saw this posted by a NJ meteorologist on Facebook. "I'll post a full weekend outlook tonight but as of now rain arrives Saturday afternoon and ends late Sunday morning. On and off showers, not continuous. Thunderstorms possible within. Be safe! JC"
Maybe there's hope for Sunday afternoon?
Oh wait! There are "other" contests this weekend? I guess so. LOL!
Aug 16-Aug 17, 1020Z-0920Z, W0DBQ, Dubuque, IA. The Great River Amateur Radio Club. 7.282 14.282 17 meters 15 meters. QSL. GRARC, POB 12384, Dubuque, IA 52004. Come and have a pick-up game with us on the air. w9upk@arrl.net or https://www.w0dbq.org
08/17/2024 | Celebrating Gene Senti's Birthday
Aug 17, 1400Z-1800Z, W0CXX, Cedar Rapids, IA. Collins Amateur Radio Club. 14.263 MHz. QSL. Brice AntonJensen, 1110 Lyndhurst Dr, Hiawatha, IA 52233. https://www.qrz.com/db/W0CXX
08/17/2024 | International Lighthouse Lightship Weekend
Aug 17-Aug 19, 0001Z-0000Z, T44IJ, Isla de la Juventud, CUBA. Radioclub Isla de la Juventud (CO9DAA), Cuba. 7.091 10.131 14.090 21.091. QSL. Vasiliy, P.O. Caja "8" , g. Novopavlovsk, distrito de Stavropol, RUSIA 357300, CUBA. La estaciΓ³n estarΓ‘ activando el Faro de Carapashibey al sur de la Isla de la Juventud, Cuba, con nΓΊmero de Isla NA-056 https://www.qrz.com/db/T44IJ
08/17/2024 | International Lighthouse Weekend 2024
Aug 17-Aug 18, 0001Z-2324Z, W7FLO, Florence, OR. Oregon Coast Emergency Repeater Inc.. 14.265.000. QSL. COCARC, PO BOX 254, Florence, OR 97439. info@w7flo.com
08/17/2024 | International Lighthouse/Lightship Weekend
Aug 17-Aug 18, 1700Z-1500Z, N6L, La Honda, CA. SC4ARC. 7.030 CW, 7.270 SSB 14.030 CW, 14.270 SSB 21.030 CW, 21.370 SSB. QSL. SC4ARC, P.O. Box 237, La Honda, CA 94020. Please do not send QSL card. Logged contacts will be sent QSL after event. www.SC4ARC.org/events/lighthouse
08/17/2024 | Nuclear Ship Savannah Maiden Voyage Anniversary
Aug 17, 1300Z-2100Z, K3S, Baltimore, MD. Nuclear Ship Savannah ARC. 7.1 14.1 21.1 28.1. QSL. K3LU, 980 PATUXENT ROAD, Odenton, MD 21113. Single transmitter SSB and CW aboard N/S Savannah. Please check spotting networks for frequencies. Info on QRZ.com www.qrz.com/db/k3s
08/17/2024 | Port Clinton, OH Lighthouse activation on Saturday, August 17th, 2024
Aug 17, 1500Z-2100Z, W8GNM/8, Port Clinton, OH. Port Clinton Lighthouse Conservency. 14.335 21.440 28.615 7.235. QSL. Geoff Mendenhall, 4720 E. Terrace Cir, 4720 E. Terrace Cir, Port Clinton, OH 43452. W8GNM/8 will be QRV from the Port Clinton Lighthouse during the Port Clinton Lighthouse Festival at Port Clinton, OH (ARLHS USA-922). Grid Square: EN81mm (http://arlhs.com/events/) International Lighthouse/Lightship Weekend Aug 17, 2024 at Port Clinton, OH. (US 0228) (https://wllw.org/index.php/list-3) Port Clinton Lighthouse Conservancy (http://portclintonlighthouse.org/) Check web clusters for specific frequencies. Typical 40m frequencies 7.200 or 7.235 Typical 20m frequencies 14.285 or 14.335 Typical 15m frequencies 21.350 or 21.440 Typical 10m frequencies 28.600 or 28.615 QSL via LoTW only to W8GNM/8. Operators: Geoff - W8GNM, Jay - K8CJY, Tom - KZ8ZZ, and Jon - KB8SRQ https://portclintonlighthouse.org
08/17/2024 | Shiremanstown Sesquicentennial
Aug 17-Aug 18, 1500Z-0300Z, K3K, Camp Hill, PA. South Mountain Radio Amateurs. 7.290 21.290 14.290 28.390. QSL. See K3K , on QRZ, Shiremanstown. Electronic QSL card provided through email and/or eQSL.cc. Fill out form on N3TWT.org to get email with Electronic QSL card. Additional information available on QRZ under K3K special events call sign n3twt.org
08/17/2024 | Thunder on the Plains
Aug 17, 1400Z-2100Z, WB5EMR, Levelland, TX. Hockley County Amateur Radio Club. 7.260 14.260. QSL. Whitney Owens, N5QNS, 332 Pecan, Levelland, TX 79336. See website for details. www.wb5emr.org
And lastly ...... overnight I got an e-mail from QRP Labs that my QMX has been shipped! Another e-mail from FedEx shows the probable delivery date? You guessed it! Monday ..... the day AFTER the Skeeter Hunt! Oh well, I'd want to take the time to go through the manual quite thoroughly anyway, so I don't destroy the radio the first time I turn it on.
I have been on 10m FT8 with my 2.5W for about 2 hours. So far (at 1104z) I have been spotted by 195 stations and here I have spotted 280 stations with the furthermost Western Australia.
UPDATE 1153z:Β Spotted VK0DS (14844km) in Antarctica. 314 stations spotted here and I have been spotted by 216 stations.
Just crossed 55,000 logged at QRZ.com: Confirmed at QRZ.com is 71.6% A new country, if evenly spaced out, would be one out of every 256 QSOs (every 233 QSOs if the 21 unconfirmed DX Countries were confirmed at QRZ.com) Domestic QSOs account for 75.6% (so DX contacts average just under one-fourth) 73 Steve K9ZW
Meetings of Bolsover Amateur Radio Society take place every other Tuesday starting at 8pm at the Bainbridge Hall, Bolsover, S44 6PX. Further information and reminders for meetings can be found on the Societyβs Facebook page @bolsoverars Β Contact Vin, G4KSY on 01246 827135 for further information. Bromsgrove and District Amateur Radio Club meets every Friday from [β¦]
Barnsley and District Amateur Radio Club has a meeting from 7pm every Wednesday. On Thursday, there will be a net on 144.5625MHz FM from 7pm. David, G4TMZ, g6aj@outlook.com Bishop Auckland Radio Amateur Club will be meeting at the Village Hall, Stanley Crook on Thursday evening from 7.30pm. Please visit the Clubβs website at barac.org.uk Β for [β¦]
Antrim and District Amateur Radio Society has 2m nets from 9pm on Tuesday and from 8pm on Saturday. adars.co.uk Bangor and District Amateur Radio Society meets on the second Tuesday of the month in the Marquis Hall, Abbey Street, Bangor, BT20 4JE from 7.30pm. For more information visit the Societyβs Facebook page. Bushvalley Amateur Radio [β¦]