In the UBA DX CW contest I usedΒ the Indoor Booster Cylinder DipoleΒ and myΒ End fed antenna.Β I used the Booster Cylinder Dipole exclusively on 21 MHz. I used the End-fed on 14 MHz, 7MHz and 3.5 MHz.
Booster Cylinder Dipole On 21 MHz I compared the Booster with the End fed. Strong signals on the End fed could be worked easily with the Booster Cylinder Dipole. Also with a lower power than 3 or 4 Watt. Hi. On 14 MHzΒ I had to use "Full Power" to make the QSO's. I used Search & Pounce for all QSO's that I made with the Booster. This gives the opportunity to lower the power, when the received signal is strong.
End Fed on lower bands Β
Β As a Low Power enthusiast I often use Search an Pounce (S&P). When the signals are strong I use S&P, instead of calling CQ withΒ the maximum power of my QRP set. Before I answer a CQ, I can adjust my power, using the S-meter reading. The stronger the signal, the lower the power can be. Propagation works both ways.
Low Power Omdat ik als Low Power enthousiast, zo veel mogelijk het laagst mogelijke vermogen wil gebruiken, geef ik in de meeste contesten zelf geen CQ, maar draai over de band, om sterke station te vinden en dan een QSO te maken met laag vermogen. Door deze werkwijze ben ik geoefend in het direct juist ontvangen van volgnummers. Maar een call moet ik meestal twee maal horen om,Β hem volledig en correctΒ te nemen.
End fed
End-fed bijΒ PA1B
Omdat ik op alle banden wilde werken, heb ik van te voren besloten om in de PACCΒ uitsluitendΒ met de end fed te werken.
Mijn end fed bestaat uit meer dan 20 meter draad. Hij wordt gevoed via een lintlijn van 300 ohm. Om te zorgen dat deze antenne in mijn achtertuin past, heb ik "Linear loading" toegepast. De draad wordt eerst over een lengte van 6 meter terug gevouwen en daarna ook weer heen te vouwen. MeerΒ info:Β <<End fed met Linear Loading>> Klik.
S&P Zoals gebruikelijk, ben ik gestart metΒ S&P. Of wel over de band draaien en sterke stations beantwoorden met 360 mW. Na 3 stations op 21 MHz gewerkt te hebben, was de koek op. Er waren geen sterke stations meer, die ik nog niet gewerkt had.
CQ op 14 MHz met 360 mW Het terug regelen van het vermogen, scheelde bijna niets. Regelmatig werd mijn CQ in CW door twee stations beantwoord. Dat is prima, want men hoort mij. Maar ook heel lastig, want ik moet een call meestal twee keer horen, om deze volledig te nemen. Maar het leuke was, dat ik op deze manier maar liefst 24 achtereen volgende QSO's met 360 mW kon maken. Dat is smullen.
7 MHz met 3 W Na het eten ben ik verder gegaan en toen heb ik omgeschakeld naar 7 MHz. Daar heb ik, zonder daar eigenlijk over na te denken, het volle vermogen van 3 watt gebruikt. Over zaterdagavond en zondagmorgen leverde dit 68 QSO's. Twee station waren zo hard dat ik die met het grootste gemak met 450 mW kon werken met S&P.
CQΒ met 360 mWΒ op 14 MHz en op 21MHzΒ Op zondagmorgen werd het tijd om weer naar 14 MHz te gaan. Aangemoedigd door het goede resultaat met het CQ geven met 360 mW op zaterdag, ben ik direct gestart met 360 mW. Dat ging uitstekend. De stations rolde binnen, soms over elkaar heen. Hi. Dit resulteerde op 14 MHz in 26 QSO's en op 21 MHz in 16 QSO's, allemaal met 360 mW.
48% met QRPp Door het succes op 14 MHz en 21 MHz met laag vermogen, werd 48% van de in totaal 151 QSO's met 360 mW gemaakt.
DXCC's en 1000 MPW De tabellen hier onder geven een overzicht over de gewerkte DXCC landen en met welk vermogen het QSO gemaakt is. Maar liefst 48% van de QSO's is gemaakt met QRPp, dat wil zeggen minder dan 1 Watt. Van elk QSO houd ik op papier bij, met welk vermogen dit QSO gemaakt is.
1000 Mijl per Watt De rode aantallen in de tabel geven aan, dat deze QSO's gemaakt zijn met "MeerΒ dan 1000 Mijl per Watt". Dat leidt ik af aan de hand van de afstand en het gebruikte vermogen. Met een vermogen van 360 milliwatt, levert een QSO met een station op meer dan 360 mijl afstand, een Meer dan 1000 Mijl per Watt QSO op. Eenvoudig toch. Op 7MHz werd ik in eens aangeroepen door K1ZZ.Β K1ZZ bevindt zich op meer dan 2700 mijl. Dus ook dit QSO is goed voor meer dan 1000 Mijl per Watt.
PA1B in de PACC 2024 Overzicht van DXCC landen
PA1BΒ in de PACC -Β BandΒ overzicht
Rig: FT-817 Antenna: End-fed Sloping down to the east.
In the EU DX contest I used the Booster Cylinder Dipole.Β I used the Booster on 15 metersΒ and on 20 metres . These bands are not always open, but I seized the oppurtunity. Hi.
Bands and Power The power of the set is 3 W on 21 MHz and 4 W on 14 MHz. All QSO's are made with search and pounce. S&P.Β I did not call CQ myself.
QSB There was some QSB. QSB can be a real showstopper, when working with QRP. If I am lucky, it is best to start, when the signal strenght goes up. Then the station will hear my call, before the signal peaks. And the QSO can be completed, before my signal fades again. Hi.
32 QSO's with 17 DXCC's I am very pleased with the results. I started on 15 m and after 3 QSO's I went to 20 m, to make 15 QSO's. Then I went back to 15 m, to make anotherΒ 12 QSO's. After that I went to 28 MHz and to my surprise,Β I could make a QSO with just 800 mW, this time on the Monster Cylinder Dipole.Β In 3 QSO's the signal was so strong, that I reduced my power to QRPp and could make twoΒ 1000 Miles per watt QSO's.
Booster TheΒ BoosterΒ is a cylinder dipole. The two cylinders, are each made from 6 Energy Booster cans fromΒ aluminium, that are cut open and bolted together. The wingspan is 55 cm or 22 inch. Hi. Click for details >>
The HA DX contest is a contest with much activity. So I decided to work with my indoor Booster Cylinder Dipole. As a low power enthusiast I always work with QRP or QRPp (less than 1 W) when possible. The stonger the received signal, the lower the power can be. The Booster hangs in the Dormer Window.
The table shows the 17 QSO's that I made on 21 MHz. 21 MHz worked more easily than the other bands. Hi. Further only one QSO on 14 MHz was made.
PA1B in HA DX 2024 with QRP on 21 MHz Booster Cylinder Dipole - Wingspan 55 cm
Booster TheΒ BoosterΒ is a cylinder dipole. The two cylinders, are each made from 6 Energy Booster cans fromΒ aluminium, that are cut open and bolted together. Click for details >>
PA1B with the Monster Cylinder DipoleΒ Wingspan 35 cm - 15 inch
I took part in the DARC 10 meter contest with the Monster Cylinder Dipole.Β This cylinder dipole is called the Monster, because it is made of twoΒ Β MΓΈnsterΒ Β Energy Drink cans and a coil. The wingspan is 38 cm which is 15 inch.
In the past I used the Monster cylinder dipole on 21 MHz. On 21 MHz the dipole is doing well. I was curious how the Monster Dipole would do on 28 MHz.
Indoor antenna with a wingspan of 35 cm The dipole is hanging in the dormer windowΒ (Im Dachfenster) and is connected to the tuner with 300 ohm twinlead. The tuner does not tune the antenna, but is adjusting the impedance.
Strong signals When I started in the DARC 10 meter contest, I noticed that the signals were strong S+. Strong signals are a good sign. Please notice that the antenne is very small, so the voltage of the received signal will be very low.Β
CW QRP S&P I always work with CW QRP.Β The first station that I worked wasΒ LZ55ZF. I answered his CQ with power of 2.7 Watt. I received an immediate correct respons and logged the contact. The distance is 1100 Miles. Not bad for an antenna with a wingspan of 35 cm or 15 inch. Hi. I was in the contest for 1 hour and 1 minute and made a total of 5 QSO's.Β
4 DXCC's I could easily work stations over a distance of 1000 miles or 1600 km with just 3 watt.
PA1B in DARC 10m contest 3 Watt in Monster Cylinder DipoleΒ
Local QRM on 10 meter The local QRM was strong. It was S9. When I switched the MorseMachine off, the local QRM was S8.Β The MorseMachine is the main source of QRM. Luckely is 10 meter the only band, on which the MorseMachine will give QRM. Switching the MorseMachine off during listening, does not work. Switching off on receive is not fast enough. I tried in a dry run, but that would in a real QSO result in missing the exchange. So I leave the MorseMachine on during the whole QSO.
I had great fun in the HA-DX Contest of 2023. I used my FT-817 QRP transceiver with CW on an End fed, that is fed via 300 ohm twin lead.
Strong signals When I started just before 15 utc on 20 meter, I heard very strong signals. A signal of S9 can be answered with 1 W or 500 mW. But the signals were very strong: S9 + 10 dB. This gives the possibility to make QSO's with 80 mW or even 36 mW. When I came on the band, I first looked for the stations that were received with S9 + 10 dB.
In the first two hours on the band I made 12 QSO's with 36 mW and 80 mW. All with search an pounce. (S&P) Only when I am sure the my signal is not heard, I will increase my power and try again. The lowest power of my FT-817 with CW is 360 mW. This 360 mW is reduced to 36Β mW with a 10 dB attenuator. My homebrew power attenuator of 10 dB
Later I made QSO's with 800 mW and 360 mW, when the signal strenght decreased. When the band closed, I went to 7 MHz. After one QSO I decided to stop because it was too difficult. My 2,7 W was not heard between all QRO-signals.
On sunday I started on 7 MHz with 2.7 Watt. Later I went to 14 MHz to make QSO's with 360 mW, 800 mW and 3.6 Watt. I use 3.6 W when my 800 mW is not heard.
Toen ik vanmorgen naar Fitness ging, zag ik bloeiende narcissen. Het is pas 26 januari en dan al bloeiende narcissen. Ongelofelijk. Vanmiddag zijn we er nog even langs gelopen. Achteraf denk ik, dat de narcissen "binnen" uitgekomenΒ zijn en daarna buiten gepland. Maar toch leuk. Hi.
I had great fun with low power in the OK/OM contest 2022. On 14 MHz I made QSO's with 360 mW and 4 watt. I use 360 milliwatt, when the signals are strong. With 360 mW to OK or OM every QSO is good for more than 1000 Miles per Watt. Within a few days after the contest, I received eQSL's. All QSO's are made with CW S&P on an Sloping Endfed antenna.
I received a very nice Digital QSL card from Antonis SX1T by e-mail.
Antonis writes that it is not an official QSL card, but I very much like it. Hi.
Antonis writes: This in
NOT a valid QSL. This is a greeting and a message. You don't have to reply with
an email QSL.Β This email was automatically created using the FREE HamTools by PA4R
The distance from my QTH to Greece is just more than 1000 miles.
So I reduced my power to 800 mW before answering the CQ of Antonis, to make a "more than 1000 Miles per Watt" QSO.
We made a QSO with 1634 Miles per Watt. Over a distance of 1307 Miles between our QTH's and aΒ power of 800 mW.
As a low power enthusiast I always try to use the lowest possible power in each QSO.
Tnx to Antonis for the very nice QSO and the very nice QSL card.
Eindgevoede draad Toen mijn inverted V in mei 2015 zodanig beschadigd was door de wind, ben ik eerst overgestapt op de Cilinder dippool, waarmee ik van 2015 t.e.m. 2016 gewerkt heb. Maar begin 2017 wilde ik weer een antenne buiten ophangen. Net voor de PACC (2017)Β heb ik daarom gekozen voor een End fed.
Ik had op vakantie veel ervaring opgedaan met de endfed, die gevoed wordt via een 300 ohm lintlijn met een lengte van 4,80 meter. De endfed in in combinatie met mijn licht gewicht vakantie tuner heeft mijn veel leuke vakantie QSO's opgeleverd. Zie:Β https://a29.veron.nl/hams/pa1b/qrp-holiday-transmatch/
Draad Ik had een lang stuk draad van meer dan 20 meter, dat ik niet door wilde doorknippen. Dus heb ik dat gewoon in zijn geheel opgehangen. Om in de achtertuin te passen moest ik de draad terugvouwen. Omdat ik 12 meter over had heb ik besloten om twee keer 6 meter terug te vouwen. Hi.
Linear loading Lineair loading is een fraaie term om het gedeeltelijk terug vouwen van een (lange) draad aan te geven. Ik heb de term ergens opgevangen, bij iemand die op deze manier zijn verticale antenne verkortte, zonder gebruik te maken van een spoel ergens in de draad. Door het gedeeltelijk terugvouwen van de draad, kan ik een grotere lengte kwijt in mijn tuin van beperkte omvang.
Staande golf Op een βzendendeβ draad staat een staande golf. Op het eindpunt is de stroom nul. En verder van het eind wordt de stroom in de draad groter. De stroom in het teruggevouwen deel loopt tegengesteld aan de stroom in de draad, waarlangs hij teruggevouwen is. Over de lengte het teruggevouwen deel heffen de magnetische velden elkaar gedeeltelijk op, waardoor het teruggevouwen deel vrijwel niet straalt. Het HF vermogen wordt door de rest van de antenne uitgestraald.
300 Ohm lintlijn In huis wordt de draad gevoed via een 300 ohm lintlijn. Dit kun je ook weer opvatten als lineair loading. Het lint brengt het HF signaal buiten de shack zonder zelf veel te stalen. De stroom in de beide aders van het lint lopen tegengesteld, waardoor de lintlijn vrijwel niet straalt. Het lint werkt als een impedantie transformator. De tweede draad van de lintlijn werkt als een counter poise. (Tegenwicht) Het antenne systeem heeft daardoor geen aardesysteem nodig. Als ik op 7 MHz werk schakel ik nog een extra stuk lintlijn van twee meter lengte tussen tuner en het lint naar de zolder. Hierdoor is de antenne dan wel (of beter) aan te passen.
During last week I carefully build up my VLF antenna to listen to the
Christmas Eve morning transmission of SAQ. This Swedish station was built
in Grimeton, just less than 100 years ago, to send telegrams from Sweden to the U.S.
on a frequency of 17.2 kHz
My Antenna
The antenna is a loop with a diameter of 1.75 meter. The loop is tuned to 17.2
kHz to receive the signals of SAQ. The loop is connected to an amplifier with
feedback to pick up the signal. First I check the antenna by increasing the
feedback of the loop amplifier to make the antenna oscillate. After the check I
reduce the feedback.
FT-817 + converter
The signal of the loop amplifier is fed into a frequency converter with a SO42P
mixer, with a 8 MHz crystal. The signal goes to the FT-817, which is tuned to
8017.2 kHz. To check the complete setup I use an Audio signal generator set to
17.2 kHz. When I can receive this signal, I know everything is all right.Β
Excellent reception When I switched on my RIG on 7:47 utc on Christmas Eve, I immediately
heard the signal of SAQ.
So the tuning with use of the Audio Signal Generator was perfect. Hi.
At the right of the loop amplifier and the converter, I had enough room to put
my A4 paper to write down the message of SAQ.
I did not copy all letters, though the signal was very good, but had fun in
writing down the CW message.
42 wavelengthsΒ
The wavelength of the signal is 17,4 km, so over a distance of 736 km from
Grimeton to my QTH there is room for just 42
wavelengths of the signal. Hi.
Table of worked DXCC's In CQ WW DX CW contest of 2020 I worked 33 DXCC's, all with
search and pounce. A contest gives an excellent opportunity to work many
stations in many DXCC countries. When the signals that I receive areΒ strong, I will reduce my power.Β
1000 Miles per Watt
When I work with very low power, I often make more than 1000 Miles per Watt
QSO's. The red numbers in the table are QSOβs that are made with more than 1000
Miles per Watt.Β
Time Diagram In the time diagram you can see the used power from QSO to QSO. This diagram is gives only the QSO's that were made on 20 meter. Because 20m was the only band where I could wordk with very low power. You can see that the Saturday was the better day, to work with less than 100 mW. When I use less than 100 mW I make use of the PA1B attenuator.
So before I could start in the CQ WW DX CW
2020, I placed all the gear back in the shack.
Delayed start
But when I started, I could not get
aΒ good SWR. In the end it took me an hour to figure out what was wrong.Β Unfortunately one of the PL259 connectors of the cable between the
set and the SWR-meter was NOTΒ screwed, in a decent way of course. After I found out, I could start. But then my
wife asked my to make a label for a return packet. This took less than an hour.
CQ WW DX CW 2020
I enjoyed the contest. I was looking forward to participate. I made a total of 139 QSO's, all with search and pounce. The RigΒ is a FT-817 with a maximum power of 4 watts. My antenna is an end fed sloping down to the east.Β
I workedΒ on 40 m, 20 m and 15m. On 20 m IΒ used a power of 4 W down to 36 mW, using the 10 dBΒ PA1B power attenuator.
Very low power
I started on 20 m with 800 mW to 4 W and then after 6 QSOβs the S-meter went up to S9+10 dB. So I could make the
first QSO with 36 mW. With 360 mW from the set and the attenuator on 10 dB. Only
on Saturday I could make a 7 QSO's with only 36 mWand just one on Sunday.
It was great to make a QSOΒ with TA3STΒ with his excellent ears.Β I first tried with 360 mW, but when my signal was not heard, I increased the power (with 3 dB) to make the QSO.Β I could barely hear him, but he could hear my 800 mW. Hi.Β FB.Β Β
In september 2019 heb deΒ NVRAΒ in Haarlem bezocht voor het geven van een lezing over de cilinder dipool. Tijdens de lezing vertelde ik dat de afmeting van de cilinder dipool evenredig met de golflengte vergroot moet worden, om te werken op een lagere frequentie. Na de lezing heb ik twee voorraad blikken voor koffie meegekregen voor een cilinder dipool voor 7 MHz. Daar heb ik begin dit jaar een cilinder dipool mee samengesteld. De spanwijdte van de dipool is 60 cm. (0.6 meter).
PA1BΒ Cilinder dipool 24" met voorraad bussen (60 cm)
Deze cilinder dipool met forse cilinders is veel groter dan de andere cilinder dipolen zoals de Monster cilinder dipool en is (daarom) geschikt voor 40 meter. Deze cilinder dipool voor 7 MHz heeft een spanwijdte van 60 cm. Dit is slechts 3% van de spanwijdte van een halve golf dipool voor 7 MHz. Echter deze cilinder dipool werkt en past met gemak in mijn dakkapel. Zelfs een cilinder dipool voor 80 meter met de dubbele afmeting zou er nog net in passen. hi.
Ik heb met deze cilinder dipool in de dakkapel QSO's gemaakt met 4 Franse stations tijdens de REF contest op 7 MHz alle 4 met 980 milliwatt.
Op 14 MHz werkt deze antenne ook heel goed. In de HA-DX contest heb ik QSO's gemaakt met slechts 360 milliwatt.Β
eQSL vanΒ F5KHPΒ in de REF contest op 7 MHz met 980 mWΒ
De opbouw van de cilinder dipool is zeer eenvoudig.
De cilinder dipool kan zo'n kleine spanwijdte hebben, door de grote onderlinge capaciteit van de twee cilinders. Een spanwijdte van 3% van die van een halve golf antenne geeft goede resultaten.